Fluke AM-PROBE AT-6030 Advanced Wire Tracer System with Clamp, Case, and Accessories

Description

(item no. 4867996)

Amprobe’s newest wire tracer combines a Receiver and powerful Transmitter to locate energized and de-energized wires, breakers, and fuses without having to disconnect any equipment. The Receiver features four tracing modes optimized for a range of applications. Its fully automatic breaker tracing capability saves time and eliminates the confusion of multiple false positives by detecting the highest recorded signal in a breaker or fuse. The Transmitter utilizes two optimized frequencies that allows for a clean and reliable signal. The Signal Clamp can be used in applications where there is no access to bare conductors by enabling the Transmitter to induce a signal into a wire through insulation. Whether you’re a novice user or an expert, the AT-6000 Amprobe Advanced Wire Tracer kit will help you get the job done fast.

Features

• Traces wires in walls, ceilings, floors and corners
• Locates breakers and fuses
• Pinpoints shorts and opens
• High resolution 2.5″ TFT LCD color display
• Three Transmitter signal modes
  • “High Signal” mode for normal circuits
  • “Low Signal” mode for precision tracing in difficult areas
  • “Loop” mode for closed loop de-energized circuits
• Four Receiver tracing modes
  • “Quick Scan” mode allows for quick wire detection at a longer distance
  • “Precision” mode precisely pinpoints wires or faults located behind walls, floors, or ceilings
  • “Breaker Identification” mode facilitates quick and easy breaker locating
  • “Non-Contact Voltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized
• Two automatically selected frequency modes for reliable tracing on energized and de-energized circuits
• Comes with custom Amprobe hard carrying case, test leads, CT-400 signal clamp, and accessories
• Compatible with optional TIC 410A Hot Stick attachment to extend your reach

Specifications

Specifications AT-6000-R Receiver AT-6000-T Transmitter CT-400 Signal Clamp Measurement Category CAT III 600 V CAT III 600 V CAT IV 600 V, CAT III 1000 V Operating voltage 0 to 600 V AC/DC 0 to 600 V AC/DC 0 to 1000 V AC Operating frequency Energized: 6.25 kHz De-Energized: 32.768 kHz Energized: 6.25 kHz De-Energized: 32.768 kHz Wire tracing: 32.768 kHz AC current measurement: 45 Hz to 400 Hz Hazardous voltage detection See NCV detection > 30 V AC/DC N/A Signal indications Numeric, bar graph display and audible beep LEDs and audible beep N/A Response time Tip Sensor (energized/de-energized): 500 MS NCV: 500 MS Battery voltage monitoring: 5 sec Line voltage monitoring: 1 sec Battery voltage monitoring: 5 sec Instantaneous Current output of signal (typical) N/A Energized circuit: HI mode: 60 mA RMS LO mode: 30 mA RMS De-energized circuit: HI mode: 130 mA RMS LO mode: 40 mA RMS Loop mode: 160 mA RMS 1 mA/A for AC current measurement with multimeter Signal voltage output (nominal) N/A De-energized circuit: LOW: 29 V RMS, 120 Vp-p HIGH: 33V RMS, 140 Vp-p  With CT-400: loop model: 31 V RMS, 120 Vp-p De-energized circuit: 2.4 V RMS, 24 Vp-p Range detection (open air) Tip sensor (Energized): Max distance via air: up to 20 ft (6.1 m) Pinpointing: approx. 1.97 in (5 cm) Tip sensor (De-energized): Max distance via air: up to 14.7 ft (4.5 m) Pinpointing: approx. 1.97 in (5 cm) NCV detection (40 to 400 Hz): Max. sensitivity: 90 V up to 6.56 ft (2 m) Min. sensitivity: 600 V up to 0.39 in (1 cm) N/A N/A Kit Contains AT-6020 kit AT-6030 kit AT-6000-R Receiver • • AT-6000-T Transmitter • • TL-6000 Test Lead and Accessory Kit • • CC-6000 Hard Carrying Case • • User Manual • • 1.5 V AA (IEC R6) Batteries (12) (not installed) • – Rechargeable Batteries (12) (not installed) – • Battery Chargers (3) – • CT-400 Signal Clamp – •

Model Name

Description

AT-6030

Amprobe AT-6030 Advanced Wire Tracer Kit Traces wires in walls, ceilings, floors and corners Locates breakers and fuses Pinpoints shorts and opens High resolution 2.5″ TFT LCD color display Three Transmitter signal modes “High Signal” mode for normal circuits “Low Signal” mode for precision tracing in difficult areas “Loop” mode for closed loop de-energized circuits Four Receiver tracing modes “Quick Scan” mode allows for quick wire detection at a longer distance “Precision” mode precisely pinpoints wires or faults located behind walls, floors, or ceilings “Breaker Identification” mode facilitates quick and easy breaker locating “Non-Contact Voltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized Two automatically selected frequency modes for reliable tracing on energized and de-energized circuits Comes with custom Amprobe hard carrying case, test leads, and accessories Compatible with optional TIC 410A Hot Stick attachment to extend your reach, HS-1 magnetic hanger, and TL-7000-25 m test lead Included Accessories: AT-6000-R Receiver, AT-6000-T Transmitter, TL-6000 Test Lead and Accessory Kit, CT-400 Signal Clamp, CC-6000 Hard Carrying Case, Rechargeable Batteries, Battery Chargers, User Manual

 Download

• Product Manual

Explore more from our collection.